Skip to main content
Version: 2.7.0

Load Scheduling with Average Latency Feedback

Introduction

This policy detects traffic overloads and cascading failure build-up by comparing the real-time latency with its exponential moving average. A gradient controller calculates a proportional response to limit accepted concurrency. The concurrency is reduced by a multiplicative factor when the service is overloaded, and increased by an additive factor while the service is no longer overloaded.

At a high level, this policy works as follows:

  • Latency EMA-based overload detection: A Flux Meter is used to gather latency metrics from a service control point. The latency signal gets fed into an Exponential Moving Average (EMA) component to establish a long-term trend that can be compared to the current latency to detect overloads.
  • Gradient Controller: Set point latency and current latency signals are fed to the gradient controller that calculates the proportional response to adjust the accepted concurrency (Control Variable).
  • Integral Optimizer: When the service is detected to be in the normal state, an integral optimizer is used to additively increase the concurrency of the service in each execution cycle of the circuit. This design allows warming-up a service from an initial inactive state. This also protects applications from sudden spikes in traffic, as it sets an upper bound to the concurrency allowed on a service in each execution cycle of the circuit based on the observed incoming concurrency.
  • Load Scheduler and Actuator: The Accepted Concurrency at the service is throttled by a weighted-fair queuing scheduler. The output of the adjustments to accepted concurrency made by gradient controller and optimizer logic are translated to a load multiplier that is synchronized with Aperture Agents through etcd. The load multiplier adjusts (increases or decreases) the token bucket fill rates based on the incoming concurrency observed at each agent.
info

Please see reference for the AdaptiveLoadScheduler component that is used within this blueprint.

info

Configuration

Blueprint name: load-scheduling/average-latency

Parameters

policy

Parameterpolicy.components
DescriptionList of additional circuit components.
TypeArray of Object (aperture.spec.v1.Component)
Default Value
Expand
[]
Parameterpolicy.policy_name
DescriptionName of the policy.
Typestring
Default Value__REQUIRED_FIELD__
Parameterpolicy.resources
DescriptionAdditional resources.
TypeObject (aperture.spec.v1.Resources)
Default Value
Expand
flow_control:
classifiers: []
Parameterpolicy.evaluation_interval
DescriptionThe interval between successive evaluations of the Circuit.
Typestring
Default Value10s
policy.service_protection_core
Parameterpolicy.service_protection_core.adaptive_load_scheduler
DescriptionParameters for Adaptive Load Scheduler.
TypeObject (aperture.spec.v1.AdaptiveLoadSchedulerParameters)
Default Value
Expand
alerter:
alert_name: Load Throttling Event
gradient:
max_gradient: 1
min_gradient: 0.1
slope: -1
load_multiplier_linear_increment: 0.025
load_scheduler:
selectors:
- control_point: __REQUIRED_FIELD__
service: __REQUIRED_FIELD__
max_load_multiplier: 2
Parameterpolicy.service_protection_core.dry_run
DescriptionDefault configuration for setting dry run mode on Load Scheduler. In dry run mode, the Load Scheduler acts as a passthrough and does not throttle flows. This config can be updated at runtime without restarting the policy.
TypeBoolean
Default Valuefalse
Parameterpolicy.service_protection_core.kubelet_overload_confirmations
DescriptionOverload confirmation signals from kubelet.
TypeObject (kubelet_overload_confirmations)
Default Value
Expand
{}
Parameterpolicy.service_protection_core.overload_confirmations
DescriptionList of overload confirmation criteria. Load scheduler can throttle flows when all of the specified overload confirmation criteria are met.
TypeArray of Object (overload_confirmation)
Default Value
Expand
[]
policy.latency_baseliner
Parameterpolicy.latency_baseliner.flux_meter
DescriptionFlux Meter defines the scope of latency measurements.
TypeObject (aperture.spec.v1.FluxMeter)
Default Value
Expand
selectors:
- control_point: __REQUIRED_FIELD__
service: __REQUIRED_FIELD__
Parameterpolicy.latency_baseliner.latency_tolerance_multiplier
DescriptionTolerance factor beyond which the service is considered to be in overloaded state. E.g. if the long-term average of latency is L and if the tolerance is T, then the service is considered to be in an overloaded state if the short-term average of latency is more than L*T.
TypeNumber (double)
Default Value1.25
Parameterpolicy.latency_baseliner.long_term_query_interval
DescriptionInterval for long-term latency query, i.e., how far back in time the query is run. The value should be a string representing the duration in seconds.
Typestring
Default Value1800s
Parameterpolicy.latency_baseliner.long_term_query_periodic_interval
DescriptionPeriodic interval for long-term latency query, i.e., how often the query is run. The value should be a string representing the duration in seconds.
Typestring
Default Value30s

dashboard

Parameterdashboard.extra_filters
DescriptionAdditional filters to pass to each query to Grafana datasource.
TypeObject (map[string]string)
Default Value
Expand
{}
Parameterdashboard.refresh_interval
DescriptionRefresh interval for dashboard panels.
Typestring
Default Value15s
Parameterdashboard.time_from
DescriptionFrom time of dashboard.
Typestring
Default Valuenow-15m
Parameterdashboard.time_to
DescriptionTo time of dashboard.
Typestring
Default Valuenow
Parameterdashboard.title
DescriptionName of the main dashboard.
Typestring
Default ValueAperture Service Protection
dashboard.datasource
Parameterdashboard.datasource.filter_regex
DescriptionDatasource filter regex.
Typestring
Default Value
Parameterdashboard.datasource.name
DescriptionDatasource name.
Typestring
Default Value$datasource

Schemas

driver_criteria

Parameterenabled
DescriptionEnables the driver.
TypeBoolean
Default Value__REQUIRED_FIELD__
Parameterthreshold
DescriptionThreshold for the driver.
TypeNumber (double)
Default Value__REQUIRED_FIELD__

overload_confirmation_driver

Parameterpod_cpu
DescriptionThe driver for using CPU usage as overload confirmation.
TypeObject (driver_criteria)
Default Value
Expand
{}
Parameterpod_memory
DescriptionThe driver for using CPU usage as overload confirmation.
TypeObject (driver_criteria)
Default Value
Expand
{}

kubelet_overload_confirmations

Parametercriteria
DescriptionCriteria for overload confirmation.
TypeObject (overload_confirmation_driver)
Default Value__REQUIRED_FIELD__
Parameterinfra_context
DescriptionKubernetes selector for scraping metrics.
TypeObject (aperture.spec.v1.KubernetesObjectSelector)
Default Value__REQUIRED_FIELD__

overload_confirmation

Parameteroperator
DescriptionThe operator for the overload confirmation criteria. oneof: `gt | lt | gte | lte | eq | neq`
Typestring
Default Value
Parameterquery_string
DescriptionThe Prometheus query to be run. Must return a scalar or a vector with a single element.
Typestring
Default Value
Parameterthreshold
DescriptionThe threshold for the overload confirmation criteria.
TypeNumber (double)
Default Value

Dynamic Configuration

note

The following configuration parameters can be dynamically configured at runtime, without reloading the policy.

Parameters

Parameterdry_run
DescriptionDynamic configuration for setting dry run mode at runtime without restarting this policy. In dry run mode the scheduler acts as pass through to all flow and does not queue flows. It is useful for observing the behavior of load scheduler without disrupting any real traffic.
TypeBoolean
Default Value__REQUIRED_FIELD__